New water heater installed right, the first time. We size the tank for your home's demand, pull the permit when one is required, and handle every part of the install — gas line, water lines, flue venting, expansion tank, code-required pan, and haul-away. No lead-fee middleman, no upsell at the kitchen table.
Every install is sized to your home's actual demand and quoted before work begins. The list below is the standard scope — code-required upgrades are quoted separately, never tacked on at the end.
We size the right tank (typically 40–50 gal for a family home) for your actual hot-water demand, then deliver it to the install location the same day.
Gas-line sizing, drip leg, and shut-off are brought up to current Nebraska gas code. We replace the flex connector and confirm proper sediment trap on every install.
Hot and cold supply lines, dielectric unions where required, and a working shut-off at the cold inlet. Nothing improvised, no push-on fittings.
We inspect existing flue for backdraft, blockage, and proper rise. Single-wall and Category I venting are brought up to current standards before the new tank is fired.
Thermal-expansion tanks are now code on closed systems. We size and install one matched to your tank, not a generic off-the-shelf fit.
If the install is over a finished living space, a code-required drip pan with a routed drain is part of the standard scope. We fabricate and route the pan to code, not just drop it under the tank.
The old tank leaves with us the same day. No separate disposal fee, no scrap tank left on the driveway.
We light the burner, confirm proper combustion, check for leaks at every connection, set temperature to a safe operational default, and walk you through shut-off before we leave.
We've been installing water heaters in Omaha since 2016. We know how Nebraska plumbing and gas inspectors read a job, what they flag, and what the inspector will pass without comment. That familiarity is what keeps installs from getting bounced — and what keeps the job finished in one visit instead of two.
Aggregator sites sell your name to the highest bidder and bake the referral fee into your final bill. Hiring us direct means the install quote is the install quote — there's no third party taking a cut on top.
When something needs adjusting after install — a temperature setting, a drip, an inspection question — you call the same crew that put it in. There's no call center routing you through a third party to find out who actually did the work.
We install and service water heaters across Omaha, including Dundee, Elkhorn, Benson, Millard, and Papillion — see all neighborhoods we serve.
A standard like-for-like tank swap typically takes 2 to 4 hours. Conversions (tank to tankless, gas to electric, fuel-source changes), code-required upgrades to venting or the drip pan, or installing a customer-supplied unit can extend the job to a full day. We confirm the timeline on-site once the existing install is visible.
Both work well in this climate. A standard tank (40–50 gallon) is the lowest-cost install and simplest to service. Tankless saves space and avoids standby-tank losses but costs more upfront and often requires a gas-line or venting upgrade. We size and quote both options on the estimate visit so you can compare before deciding.
Yes. Haul-away of the old unit is included in every install quote — no separate disposal fee. The old tank is removed from the home the same day, not left on the curb.
Water-heater replacements in Omaha can require a plumbing permit depending on scope; gas-line work almost always does. We pull the permit, schedule any required inspection, and install to current Nebraska plumbing and gas code — including the code-required drip pan, expansion tank, T&P discharge piping, and proper flue venting.
Yes, as long as the unit is new in the box, properly sized for your home's demand, and matches the fuel type and venting class in your mechanical room. We cannot install used or damaged tanks. When you supply the unit, labor pricing is separate from equipment pricing.
Tank sizing and delivery, gas-line connection, hot/cold water-line connections, flue venting, expansion tank, code-required pan, old-unit haul-away, and a startup with leak check. Code-required upgrades discovered on-site (new gas line, venting rework, drain pan routing) are quoted separately before any extra work begins.